Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Listed here in the next paragraph you can discover more quality resources pertaining to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can move rapidly; if you need to open a wall to eliminate the old tub and position the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the brand-new one. See to it you have actually certified yourself for the task and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous water supply pipes.
Your devices and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed position. The wooden boards are practical in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least once as this will certainly resolve it into its final position.
Preparing for the Installation
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about Installing A Bathtub from someone on another web page. Are you aware of another individual who is occupied with the topic? Why not share it. We truly appreciate reading our article about How to Install a Bathtub.
Click Here
Report this page